CognitiveTPG A798 Manual de instrucciones Pagina 13
- Pagina / 121
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2: Diagnostics and Conguration 13
Revision C 12/09
A798-PG00001C
For more information about See this section
Accessing the remote diagnostic tallies “Command descriptions” in Chapter 4: Programming commands
(Status commands: Transmit printer ID, remote diagnostics extension,
Hexadecimal 1D 49 40 n)
Print test and conguration menu samples will vary per model or printer
conguration. (Shown approximately 60% of size.)
When the printer is congured for USB, this
location will show either: “USB Driver Type: Native”
, “USB Driver Type: Printer Class”, or “USB Driver:
Comm Class”.
To enter Printer Config Menu :
1) Flip DIP switch #1 down
2) Reset the printer, while holding
the Paper Feed button down
Model number : A798-720D-TD00
Serial number : C073400014
Boot Firmware
Revision : V1.00
CRC : 08D3
P/N : 189-7940154A
Flash Firmware
Revision : V1.00
CRC : D70C
P/N : 189-7940155A
H/W parameters
Flash Memoriy Size : 2 Mbytes
Flash Logos/Fonts : 1152 kbytes
Flash User Storage : 64 kbytes
Flash Journal Size : 64 kbytes
SRAM Size : 128 kbytes
CPU Clock Freq. : 50 MHz
Head setting : C
Pre-Heating : Disabled
Print Density : 100%
Max Speed : 150 mm/sec
Paper Width : 80 mm
Max Power : 55 W
Knife : Enabled
Partial Cut : 125 steps
Paper Low Sensor : Disabled
Comm. Interface
RX Buffer Size : 4096
Interface type : RS232/USB
Parameters
Baud Rate : 115200
Data Bits : 8
Stop Bit : 1
Parity : NONE
Flow Control : DTR/DSR
Reception Errors : Ignore
USB Driver Type : Printer Class
USB Packet w/Error : Reject
Resident Code Pages : 437, 850, 852, 857, 858
860, 863, 865, 866
1252, 862, 737, 874
A715 CP850 Emulation : Disabled
Logo(s) defined : YES
User Char(s) defined : NO
Journal Unused : 64 kbytes
Diagnostice : OFF
*** A798 – Diagnostics Form ***
- Programming Guide 1
- Contents 3
- 4 Revision C 12/09 4
- 6 Revision C 12/09 6
- 8 Revision C 12/09 8
- A798 Programming Guide 10
- Chapter 1: About this Guide 10
- Revision C 12/09 10
- A798-PG00001C 10
- Start-up Diagnostics 11
- Runtime diagnostics 12
- Remote diagnostics 12
- Comm Class” 13
- Indicators 14
- Printer conguration 15
- Conguring the printer 16
- Communication interface 17
- Diagnostic modes 18
- Printer emulations 19
- Overview of commands 23
- Comparison to A793 23
- Character appearance 25
- Print zones 25
- Rotated printing commands 26
- Emulation modes 27
- Commands listed by function 29
- Text characteristics 30
- Graphics 31
- Bar codes 32
- Page mode 32
- User data storage 32
- Command conventions 33
- Command descriptions 34
- Generate tone 35
- Initialize printer 35
- Select cut mode and cut paper 38
- Print test form 38
- Print and paper feed 39
- Add n extra dot rows 40
- Print and feed paper 41
- Print and feed n lines 41
- Horizontal tab 42
- Set column 42
- Set vertical line spacing 44
- Set horizontal tab positions 44
- Set relative print position 45
- To move to the left: 45
- Select justication 46
- Set left margin 46
- Set printing area width 47
- Text characteristics commands 48
- Select pitch (column width) 49
- Select print mode 50
- 51
- Cancel user-dened character 53
- Select or cancel italic print 54
- Select character size 57
- Select bit image mode 60
- Print Flash Logo 62
- Dene Flash Logos 62
- Select the current logo 62
- Dene downloaded bit image 63
- Print downloaded bit image 64
- Print raster graphics 65
- Status command introduction 65
- Batch mode 65
- Transmit paper sensor status 67
- Transmit printer ID 68
- Transmit status 71
- Send printer software version 72
- Real time commands 73
- Moving data through the buer 74
- Real time status transmission 74
- Real time request to printer 77
- Real time commands disabled 78
- Unsolicited status mode 79
- Print bar code 84
- Print multiple barcodes 85
- 29 107 n d1... 00 87
- 29 107 m nL nH d1... dn 87
- Select PDF 417 parameters 88
- Select bar code width 89
- Sample symbol description: 89
- Select page mode 91
- Select standard mode 92
- Set print area in page mode 93
- Execute macro 95
- Erase user ash sector 99
- Flash download 100
- Get rmware CRC 101
- Return microprocessor CRC 101
- Erase selected ash sector 102
- Reset rmware 102
- Return main program ash CRC 102
- Appendix A: 104
- Appendix B: 108
- Resident Character Sets 108
- Code page 737 (Greek) 109
- Code page 850 (Multilingual) 110
- Code page 852 (Slavic) 111
- Code page 857 (Turkish) 112
- Code page 860 (Portuguese) 114
- Code page 862 (Hebrew) 115
- Code page 865 (Nordic) 117
- Code page 866 (Cyrillic) 118
Relacionado con productos y manuales para Impresión y escaneo CognitiveTPG A798
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales